Owatrol 1 Litre Net-Trol Wood Cleaner by OWatrol

Product Information

Interior – Sand wood with 100 grit paper to open the pores, dust off and degrease the surface with methylated spirits. Note: Any rags, steel wool etc. soaked in D1 may spontaneously catch fire if improperly discarded. Rags, steel wool etc. must be saturated with water after use or placed in a sealed, water filled metal container, before disposing of it with household waste. Maintenance Note: Hardwoods including exotic hardwoods and woods rich in tannins (i.e. Cedar, Douglas Fir, Teak, Ipe) may darken with Aquanett and Dilunett. Neutralising with Net-Trol immediately after rinsing will lighten and restore the woods colour. Application tools Net-Trol is not only for use on wood surfaces though – you can also use it to restore the lustre to faded plastics dulled by weathering and UV rays. It can also be used to remove rust stains and to clean discoloured stone and cement. Net-Trol is biodegradable and does not contain solvents or bleach. It’s not harmful to plants and shrubs so it’s safe to use in the garden! Ideal Uses for Net-Trol Wood Cleaner As Dilunett is biodegradable and non flammable, it is even safe to use in poorly ventilated or confined areas.

Ideal for surfaces difficult to strip due to size or intricate design and horizontal and vertical surfaces. We recommend protecting and enhancing the natural beauty of your wood with Owatrol penetrating wood finishes. Restrictions Scrub surface with a stiff nylon/synthetic brush whilst rinsing with water or use a pressure washer (max. 60 bar). Do not allow Dilunett to dry on the surface. If drying occurs dampen with mist application of water.Superficies horizontales o verticales: terrazas, revestimientos, vallas, cubiertas de barcos, muebles de jardín, … Dilunett is our amazing solvent free paint and coatings remover. It is powerful enough to remove up to 8 previous coatings in just 1 application! It’s ideal for stripping large areas as Dilunett is non-flammable, does not dry out and remains active a long time. First, wet the surface with clean water, then apply Net-Trol with a synthetic brush or long pile roller and agitate the surface with the brush.

Remove any loose and flaking finish. Brush off any physical surface contamination e.g. moss, general dirt etc. Shake or stir product well before and during use including diluted solutions. Easy to apply, Dilunett dissolves paint in even the smallest of recesses and the finest of details, softening all the layers for a simple and clean removal. Clean weathered wood with Net-Trol, to remove the loose wood fibres, dirt and other surface contaminants. If the wood is severely contaminated, clean it with Aquanett and neutralise with Net-Trol. Previously oiled surfaces As there are a few steps you need to take to get your project looking its best again, we thought we’d create a little post to show you which Owatrol products you should use for removing paint, varnish or stains. Which product should I use? Allow to dry for 48 hours or until it meets the moisture content required by the chosen finish before finishingAfter rinsing ALWAYS neutralise surface with Net-trol except where Tropitech is the chosen finish (see “After stripping/cleaning”). Do not use a wire brush to scrub the surface. Wet surface with fresh, clean water. Apply Owatrol Net-Trol. Scrub surface to agitate the Owatrol Net-Trol. Leave to stand for approx. 10-20 minutes. If surface starts to dry, dampen with a mist application of water. Scrub surface while flushing with water or use a pressure washer (max. 60 bar/870 psi). Rinse thoroughly with fresh clean water. If required repeat procedure. DO NOT allow Deks Olje D1 to become dry or touch dry between applications. Leave the final application for 30 minutes, then wipe over the surface to remove excess and puddled material with a rag soaked in Deks Olje D1 and rung out so that it is damp to the touch. If necessary occasionally ring out the cloth to keep it damp. It is important that as much D1 as possible is applied on the first day. Owatrol Net-trol Wood Cleaner & Colour Restorer is best used to clean and restore the colour of exterior timber. It can be used on all species of softwoods including pressured treated timber, larch, pine, cedar etc. and hardwoods such as teak, iroko, ipe, bangkirai (balau), oak, chestnut etc. it can also be used to restore faded plastic and GRP, clean discoloured stone and stained cement. Application Wet surface with fresh clean water. Apply Owatrol Net-Trol. Leave to work for 10 minutes. Scrub surface with a soft or medium scrubbing brush. Rinse with large amounts of fresh clean water.

After stripping and rinsing, surfaces must immediately be treated with Net-Trol while still wet to neutralise the surface. After stripping and rinsing. All porous surfaces must be immediately treated with Net-trol while still wet to neutralise the surface. Clean up Leave the Net-Trol to stand for approximately 15 – 20 minutes. If the surface starts to dry, you must moisten it again by using a spray of mist application of water. If you are collecting timber products please collect at the time bookedi.e. 9am collection would be 9am > 9:45am, this helps us have the product ready for your slot and reduces customer congestion. Exterior wood – weathered grey or dirty: Cedar, Larch, Pine (pressure treated or not), Teak, Iroko, Ipe, ...The driver must have assistance to offload unless alternative arrangements made with our transport team

We hope you found this post on how to clean rust stains from your patio interesting. If you have any other advice or top tips, please feel free to leave them in the comments below. We love hearing from you!

After Clean Up

Clean all tools and equipment with white spirits while still wet. If allowed to dry, remove with paint stripper. Wipe up any drips or runs immediately with a cloth soaked in white spirits. Dried Deks Olje D1 may be removed with Dilunett. Store and maintain equipment as directed by manufacturer. Always read the Dilunett Gel Product Information before using and follow the instructions carefully. Leave to stand for approx 10-20 minutes. If surface starts to dry, dampen with a mist application of water. Remove Dilunett and dissolved paint with a stiff nylon scrubbing brush or paint scraper while flushing with water. The use of hot water makes this part of the job easier. Alternatively, you can use a pressure washer (max 60bars / 870psi).