RUSTINS Metal Laquer, Clear, 125 ml (Pack of 1)

Product Information

This clear coat lasts for only 24 hours after activation. Use it within that time for quality results. However, you can preserve it in the fridge to use at a later time only that its quality shall have gone down. Clean the metal surface and remove any loose rust. Use a Cleaner Degreaser to remove grease. The Cleaner Degreaser should be water-based and non-flammable. Unlike other degreasing chemicals, Cleaner Degreaser doesn’t emit unpleasant or offensive odor. Use this Cleaner on painted surfaces as well.

Plastikote Quick Dry Clear Lacquer Spray Paint Matt 400ml Plastikote Quick Dry Clear Lacquer Spray Paint Matt 400ml

The result will be a transparent, flat layer of protective coating. Your metal will regain its shiny, newly polished look.These two formulas can also be found in 8 oz (236.6 ml), 32 oz (946.6 ml), 1, and 5-gallon containers. The ready-to-spray formula, on the other hand, comes in 32 oz (946.6 ml), 1, and 5-gallon (3.8 and 19 L) containers. Stand at a distance of 10-15 cm (3.9-5.9 in) away from the metal when spraying. One or two layers of this coat will be enough and wait for 10-15 minutes before applying the second layer. 2K SprayMax works just like a conventional spray gun; hence, you will take a short spraying time. With its self-leveling capabilities, this clear coat can seal metals without any additives or hardener. Just one single layer is enough to give sturdy and durable results than a two-part coating. Because of its transparency, the clear coat will not cover your metal’s base paint but give it a shiny new look.

Metal Laquer | Rustins

All metallic surfaces must be thoroughly cleaned and not bear any dust or debris to avoid unfavorable results. For long-lasting results, it is recommended that you apply two coats of this clear coat. Leave it to dry up after application completely. Remove any residue remaining from previous finishes using the appropriate products and methods for the finish to be removed. Clean the piece to be lacquered; acetone is ideal as an ideal general purpose cleaner and degreaser. Surfaces must be clean, dry and free of all grease, oil, salt and other surface contamination. Use an appropriate solvent depending on the substrate and contamination e.g. Acetone or Owaclean, to clean the surface prior to any of the following preparation processes. Round off any sharp edges to allow better film build. Ferrous Metals (New or Rusted): EVERBRITE clear coating can be used on painted or unpainted metals to give long-term protection or restoration. This protective metal coating can protect the metal from fading, chalking, corroding, and tarnishing. You can also use Rust Bullet Clear Shot Protective Coating on gasoline tanks to make them resistant to chemical elements and fuel solvents. After use, shut the lid tight because if not properly stored, Rust Bullet can harden rendering it useless for another application.If you have to set the item on a surface to spray it you must make absolutely sure the surface is dust free all around. The air pressure from the spray will stir up any dust and spread it evenly on your otherwise perfect finish.

How to Lacquer Metal | Architecturals.net How to Lacquer Metal | Architecturals.net

After application, let it dry for 24 hours before using the metal. However, depending on the temperature of the environment, drying could take a longer or shorter time; 12 hours if the ambient temperature is at 68°F (20°C), 35-45 minutes at 140°F (60°C) metal temperature. ProtectaClear Coating creates an impermeable finish that preserves all types of metal. A single quart bottle of this clear coat can be used to coat up to 250 sq ft (27.8 sq yd) of metal. ProtectaClear Coating gives metal protection from the effects of corrosion, rust, oxidation, and tarnish.

Ideal uses for Oxid Vernis

An EVERBRITE protective coating kit comes with Nitrile gloves, an applicator, and coating instructions. The instructions are easy to follow. You can use a lint-free cloth, paint sprayer, sponge brush, or an applicator pad to coat. Use a neutralizing solution then rinse with clean, fresh water. Any acid present will react with this clear coat’s solvents, which will darken the metal. Remove any residual coatings with alcohol. Spray Max 2K Urethane Coat is perfect for both metal repairs and long-lasting sealing. This capability is because this high gloss coat is very resistant to scratching and any other form of abrasion. Furthermore, it is highly resistant to chemicals, gasoline, acid, and harsh weather. Spray Max 2K Urethane Coat can also be used in hot temperatures without causing any color deviations. Clear Guard is UV stable, can withstand harsh weather, and resistant to water, salts, chemical damage, marring, and perspiration. Clear Guard is made in three formulas; Normal, environmentally friendly, and pre-thinned formula ready for spraying. The Normal and Environmentally friendly formulas come in 12oz spray cans.